Water Softener Installation in Orange County, CA
Hard water wrecks heaters, spots fixtures, and shortens appliance life. White Glove Plumbing & Restoration installs metered-demand water softeners that regenerate only when needed, sized to your hardness, household use, and flow rate—with tidy plumbing, air-gapped drains, and a documented setup.
✓ Softer water: scale and spotting reduced
✓ Smart metering: regenerates only as needed
✓ Right-sized: flow and capacity matched
✓ Clean install: code drains and air gap
✓ Softer wate
✓ Smart metering
✓ Right-sized
✓ Clean install
What Is Water Softener Installation (Metered Demand)?
A turn-key install of a metered (on-demand) ion-exchange softener that measures water use and regenerates only after a set capacity (grains) is consumed.
We size the resin bed to your hardness and household flow, plumb a bypass, route a code-correct drain with air gap (and brine overflow), program the control head, sanitize, and verify results at taps.
Why Choose White Glove Plumbing
Compliance & safety first: Air-gapped drain, proper standpipe/trap, backflow considerations, and neat, accessible shutoffs.
Defensible documentation: Hardness/TDS numbers, program settings, and before/after readings.
Beyond a swap: Pre-filters, blending valve options, resin cleaners, and salt storage set-ups; irrigation/exterior bypass routing.
One accountable team: We can protect your tank/tankless/heat pump heater, add post-filter testing, and service on a cadence.
Immediate Actions (What to Do Now)
Tell us symptoms (spots, soap issues, heater noise).
Share water source (city vs. well) and any past test results.
Snap photos of the proposed install area and main shutoff.
List fixtures to bypass (irrigation, exterior hose bibs).
Call our 24/7 dispatcher—we’ll test, size, and schedule.
Common Situations We Handle
Hardness > 8–10 gpg causing scale/spotting
Tankless/tank heaters scaling or running noisy
Etched glassware, soap film, dry skin complaints
Well water with hardness and light iron/manganese (with pre-treatment)
Homes adding recirculation that need scale control
Test, Survey & Size
Measure hardness (gpg/ppm), TDS, iron/manganese (spot), flow & pressure; confirm occupants/fixtures; calculate grain capacity & service flow (SFR).
Design & Prep
Choose resin type (8–10% crosslink; fine-mesh for light iron), tank size, bypass/blending approach; plan drain with air gap and brine overflow; pull permit if required.
Set & Plumb
Place resin and brine tanks; install full-port isolation, unions, and bypass; route irrigation/hose bibs around softener; add sediment/carbon pre-filter if scoped.
Drain, Power & Safety
Pipe drain to approved standpipe/sink with air gap; connect brine overflow; provide 120V to control head (if required); secure lines and label valves.
Program & Sanitize
Enter hardness, capacity, reserve, and regen time; fill brine, add salt, perform startup sanitization and a manual regeneration; check for leaks and proper draw/refill.
Commission & Handover
Verify post-softener hardness (target near 0 gpg or blended), confirm pressure drop/flow, set blending if desired, and deliver settings + maintenance guide.
What’s Included
On-site water testing & sizing (hardness/TDS, flow/pressure)
Metered control head programmed to your usage
Resin & brine tanks with bypass and unions
Air-gapped drain and brine overflow to approved termination
Startup sanitization & verification readings
Documentation packet (settings, photos, care schedule)
Costs & Timelines (What to Expect)
Typical duration: 2–6 hours depending on access and drain route.
Cost drivers: Resin/tank size, 10% crosslink/fine-mesh upgrades, pre-filter, drain distance/air gap, bypass reroutes for irrigation/exterior taps.
Clear estimate: Line items for equipment, plumbing, drain/electrical, startup, and documentation—no surprises.
Insurance & Compliance Support
Inspector-ready: Air gap, drain path, labeling, and accessible shutoffs.
Policy alignment: Local plumbing/backflow rules and manufacturer specs; COIs for HOAs/PMs.
Warranty help: We document settings and service dates for claims.
Risks of Waiting (Why Act Now)
Scale buildup in heaters, valves, and fixtures
Higher energy use from insulated heat-exchange surfaces
Frequent cleanings and spotted glass/finishes
Premature appliance failure (dishwashers, laundry, tankless)
Methods, Materials & Quality Standards
Resin: 8–10% crosslink NSF/ANSI 61; fine-mesh for light iron (with resin cleaner).
Valving: Full-port shutoffs, labeled bypass, and union connections for service.
Drainage: Air gap to approved receptor; separate brine overflow route.
Programming: Capacity/reserve tuned to hardness & use; metered regen at low-impact hours.
Salt options: Sodium or potassium; grid plate in brine tank; resin cleaner schedule on well/iron.
Blending: Optional valve to leave 3–7 gpg for feel/taste if desired.
Frequently Asked Questions
Metered vs. timer softener?
Metered regenerates only after capacity is used—saves water and salt.
Does softening lower TDS?
No—softeners exchange hardness, they don’t remove total dissolved solids. RO lowers TDS at drinking taps.
Sodium in softened water—safe?
Adds a small amount; choose potassium chloride or blending if you prefer. We can also set RO at the kitchen.
Will this protect my tankless?
Yes—dramatically reduces scale. We still suggest an annual check/flush.
Do I need a drain nearby?
Yes—for regen and brine overflow. We’ll route to an approved, air-gapped receptor.
Maintenance?
Keep salt above the grid, clean the brine tank occasionally, and use resin cleaner if you have iron. We can set a service reminder.
More White Glove Plumbing Water Softening Equipment Services
Proudly Serving All of Orange County
Address: 1430 E Borchard Ave, Santa Ana, CA 92705
Phone: (949) 209-5206
Email: office@whitegloveplumbingca.com
White Glove Plumbing is locally based in Santa Ana and serves residential and commercial clients across Orange County with 24/7 emergency plumbing and water-damage restoration.
Our expert team handles leak detection, emergency plumbing, water extraction/dry-out, sewage cleanup, mold remediation, and reconstruction in top OC areas including Irvine, Anaheim, Santa Ana, Orange, Tustin, Costa Mesa, Newport Beach, Huntington Beach, Mission Viejo, Lake Forest, Fullerton, Yorba Linda, Laguna Beach, Dana Point, and San Clemente - plus surrounding neighborhoods.
Let’s start a conversation
Book Your Free Consultation call Now
Contact us:
CALL (949) 209-5206
1430 E Borchard Ave, Santa Ana, CA 92705