Garbage Disposal Replacement in Orange County, CA
A failing disposer can leak, jam, trip breakers, and stink up the kitchen. White Glove Plumbing & Restoration provides professional garbage disposal replacement—we size the right unit, install and wire it to code, align drains and dishwasher connections, and test for quiet, smooth operation with full documentation.
✓ Licensed installation: Code-compliant plumbing and electrical connections
✓ Right-sized unit: From compact 1/2 HP to quiet, high-torque 1+ HP models
✓ Leak prevention: New flange/seal, aligned trap, and correct dishwasher knockout
✓ Clean finish: Balanced, quiet operation with splash baffle and deodorize tips
✓ Licensed installation
✓ Right-sized unit
✓ Leak prevention
✓ Clean finish
What Is Garbage Disposal Replacement?
A service that removes the failing disposer and installs a new, properly sized unit with a sealed sink flange, correct dishwasher inlet knockout, cord or hardwire per code, and aligned P-trap/discharge.
We verify quiet balance, no leaks, correct reset/rotation, and provide use/maintenance guidance.
Why Choose White Glove Plumbing
Compliance & safety first: Technicians trained in GFCI, cord/hardwire, and trap alignment to meet code.
Documented quality: Before/after photos, model numbers, wiring method, and leak/operation checks.
Beyond the swap: We can replace angle stops/supplies, re-set the basket strainer, and correct drain slope/vent issues.
One accountable team: If leaks caused cabinet damage, we can dry and sanitize immediately.
Immediate Actions (What to Do Now)
Shut off power at the switch/breaker before touching the unit.
Do not reach inside the disposer—use the supplied jam key/hex only if safe.
Avoid harsh chemicals that can damage seals and piping.
Place a bowl/tray under the disposer if it’s leaking.
Call our 24/7 dispatcher—we’ll isolate power/water, remove the old unit, and install a reliable replacement.
Common Situations We Handle
Leaking housings/flanges or rusted-out disposers
Frequent jams and manual resets; humming without grinding
Electrical trips or improper/non-GFCI connections
Dishwasher backing into sink due to missing air gap/knockout issues
Odors and splash from worn baffles or misaligned traps
Capacity/quiet upgrades during kitchen refreshes
Secure & Survey
Kill power, verify GFCI/circuit, inspect flange, basket strainer, trap alignment, and dishwasher connection/air gap.
Isolate & Protect
Pad the cabinet, place a catch pan, and disconnect power and discharge plumbing.
Remove & Prep
Remove the old unit; clean the sink flange area; set new flange and seal (plumber’s putty or gasket per manufacturer).
Mount & Wire
Hang the new disposer; install cord or hardwire with strain relief to code; confirm proper bonding and switch/GFCI function.
Plumb & Connect
Align discharge to P-trap, set correct slope; knock out dishwasher port if used; install air gap where required.
Test, Balance & Deodorize
Run water and grind ice/lemon peel to check balance, vibration, and leaks; verify reset operation and provide care tips.
What’s Included
Old unit removal and cabinet protection
New disposer install with flange/seal and mounting system
Electrical connection (cord or hardwire) with strain relief/GFCI check
Trap/discharge alignment and dishwasher connection/air gap as required
Operational test (quiet balance, grind, reset) and leak check
Documentation packet (photos as appropriate, model, wiring/plumbing notes)
Costs & Timelines (What to Expect)
Typical duration: Most replacements finish same visit; rewiring or air-gap/branch corrections may be phased.
Cost drivers: Horsepower/sound package, cord vs. hardwire, trap/branch rework, air gap requirement, and after-hours access.
Clear estimate: Line items for unit, installation, electrical/plumbing adjustments, and reporting—no surprises.
Insurance & Compliance Support
Records your stakeholders expect: Photos, model/serial, wiring method, and leak/operation verification.
Policy alignment: We follow building SOPs, provide COIs, and meet local air-gap/GFCI requirements.
Claims clarity: Separate diagnostics vs. replacement vs. mitigation available on invoices.
Risks of Waiting (Why Act Now)
Cabinet/subfloor damage from ongoing leaks
Electrical hazards from wet connections or improper wiring
Odors/pests from decomposing debris in a non-working unit
Dishwasher performance issues from backflow or poor drain tie-in
Methods, Materials & Quality Standards
PPE & site care: Nitrile gloves, eye protection; cabinet/floor protection and tidy cleanup.
Materials: Manufacturer-specified mounting rings, NSF/ANSI components, stainless hardware, cord kits where used, and proper splash baffles.
Electrical: GFCI-protected circuit, correct cord/hardwire with strain relief, listed connectors, accessible switch.
Plumbing: Sealed flange/basket, aligned P-trap, correct dishwasher knockout and air gap per code.
Testing: Leak, vibration, and load tests; instruction on safe operation and maintenance.
Training: Code-compliant kitchen fixture/electrical coordination and manufacturer procedures.
Frequently Asked Questions
Corded or hardwired—which should I use?
Both are code-acceptable when done properly. Cord kits offer easy service; hardwire is common on older installs. We’ll recommend based on your setup and code.
Do I need an air gap for my dishwasher?
Many jurisdictions require it. We’ll install or correct air-gap routing per local code.
What size disposer should I get?
For most homes, 3/4 HP balances torque and quiet. We’ll match horsepower and sound package to your needs.
Can you haul away the old disposer?
Yes—haul-away and recycling are available.
Will you replace my basket strainer or angle stops if needed?
We can reset/replace strainers and upgrade angle stops/supplies during the visit.
How do I keep it smelling fresh?
Cold water during grinding, avoid fibrous materials, and ice + citrus peel occasionally to clean baffles and chamber.
More White Glove Plumbing Emergency Plumbing Services
Proudly Serving All of Orange County
Address: 1430 E Borchard Ave, Santa Ana, CA 92705
Phone: (949) 209-5206
Email: office@whitegloveplumbingca.com
White Glove Plumbing is locally based in Santa Ana and serves residential and commercial clients across Orange County with 24/7 emergency plumbing and water-damage restoration.
Our expert team handles leak detection, emergency plumbing, water extraction/dry-out, sewage cleanup, mold remediation, and reconstruction in top OC areas including Irvine, Anaheim, Santa Ana, Orange, Tustin, Costa Mesa, Newport Beach, Huntington Beach, Mission Viejo, Lake Forest, Fullerton, Yorba Linda, Laguna Beach, Dana Point, and San Clemente - plus surrounding neighborhoods.
Let’s start a conversation
Book Your Free Consultation call Now
Contact us:
CALL (949) 209-5206
1430 E Borchard Ave, Santa Ana, CA 92705